There's no doubt it will bow, but probably not too much. My 96x24x30 bowd about 1/2" or so. It was pretty bad when you looked at it from the side.
Glass/Acrylic Thickness Calculations
- Thread starter Pharaoh
- Start date
There's no doubt it will bow, but probably not too much. My 96x24x30 bowd about 1/2" or so. It was pretty bad when you looked at it from the side.
Hi Bobby.... i am looking at building a glass tank of 10'X3'X2'... you think 18mm should suffice? with only top bracings as i would prefer not to have the bottom support... just incase i wanna go bare bottom... any advice and help very much appreciated...
Thanks,
N
Thanks,
N
Hi!
How big can I go with acrylic in 25mm?
I'm not a clever man, and I can't figure out the calculators...
How big can I go with acrylic in 25mm?
I'm not a clever man, and I can't figure out the calculators...
3/4" or more would work. If you want extra security on the bottom, go a bit thicker and that would give you more seam strength.
Depends on the length of the tank.
Roughly....
36 x 24
48 x 24 (pushing it, but OK)
72 x 20
i am looking forward to build a glass tank which is 6 ft high, but would only contain 3 ft water.
Most of the calculators are based on the assumption of all 4 sides being simply supported.
However in my case 32-36" of water column can be made using 15mm glass.
I am using a metal frame here.
What would change if we move the top support by another few feet ?
Sent from my GT-I9100G using MonsterAquariaNetwork App
Most of the calculators are based on the assumption of all 4 sides being simply supported.
However in my case 32-36" of water column can be made using 15mm glass.
I am using a metal frame here.
What would change if we move the top support by another few feet ?
Sent from my GT-I9100G using MonsterAquariaNetwork App
I'm going to need a picture or a design of what you are trying to accomplish here. It is unclear to me how you intend to support the tank. That being said, I would never use 15mm on a 36" depth. That is just asking to have water on your floor.
Its basically a paludorium with half water. I am currently designing a metal frame for it and going through fea for the same , 15mm is not really the important thing here , the question is should we design a tank for just the water column height or for the glass panel hieght.
Eventually i might even go for acrylic of a suitable thickness.
Hope this helps. Will post a pic when the 3d model takes shape.
Oh btw this is a one side view frp tank 20 x5 x6 ft with only the front being glass .it might have either 4 windows if its glass or 2 if its acrylic.
Sent from my GT-I9100G using MonsterAquariaNetwork App
Eventually i might even go for acrylic of a suitable thickness.
Hope this helps. Will post a pic when the 3d model takes shape.
Oh btw this is a one side view frp tank 20 x5 x6 ft with only the front being glass .it might have either 4 windows if its glass or 2 if its acrylic.
Sent from my GT-I9100G using MonsterAquariaNetwork App
Hello guys, I am planning to build a new tempo tank until my main project is finished. I am wondering on which thickness of glass I should use to save some cash
. The dimension/s that I was planning on is a small one, a 4'x30"x18" glass tank.
I found this calculator, http://www.garf.org/tank/BuildTank.asp , I don't know if I should trust this 100%. I'm looking to save a few bucks, here and there until budget permits, so I am planning on using 1/4" thick glass(same with the braces inside the tank and the top part).
Question now is that, will it break? Will this be too much of a risk? Should I opt for 3/8" or better yet, 1/2"?
. The dimension/s that I was planning on is a small one, a 4'x30"x18" glass tank. I found this calculator, http://www.garf.org/tank/BuildTank.asp , I don't know if I should trust this 100%. I'm looking to save a few bucks, here and there until budget permits, so I am planning on using 1/4" thick glass(same with the braces inside the tank and the top part).
Question now is that, will it break? Will this be too much of a risk? Should I opt for 3/8" or better yet, 1/2"?
HI i've found a sheet of tempered glass 72"x36"-3/8" Thick. Would this be strong enough for a 75"x34"x37" high plywood tank viewing window? The glass would be framed in by 1 1/2" and the viewable glass would be 4" of bottom of tank and the waterline on top would be even with the top of viewable glass so 33" of glass exposed. What do you all think? Is it safe? Thanks