4300 Gallon Plywood Build (3600+ Take 2)
- Thread starter nolapete
- Start date
- Status
Party @ Petes!!!nolapete;3924816; said:
I hope we do not hear from him for a while...buddy better be gettin 'er dun!!
Well wishes for him to have all the supplies and the right temp to do the JoB!!
can't wait to see more pics!Congrats....now wait til you try to open those damn buckets. It's not your typical 5 gallon paint bucket! There is a rubber seal in there that really holds the bucket shut. It's a battle to open every time! Have fun!
Asked Ken about getting the heater he told me I could borrow. It's still too cold to apply out in the fish room. Saturday I have the aquarium society meeting. Sunday I'm hoping to cut in the seams and apply the mesh tape in all the corners. We'll see.
I located the beaded board I'm going to use in the ceiling at Lowe's, so that's a relief.
Close in the ceiling
Finish painting the room
Finish building and plumbing the filters (friend is loaning me pumps temporarily)
Seal the tank
Build the heater module
I still need thermostats with submersible probes. The normally closed solenoid valve should be easy to find. Until I find thermostats I can use, heating is against a brick wall.
That's all that is left to do.
I have to replace the AC window unit with a heat pump/dehumidifier unit. Fortunately, 220 outlet is already there with existing unit.
I located the beaded board I'm going to use in the ceiling at Lowe's, so that's a relief.
Close in the ceiling
Finish painting the room
Finish building and plumbing the filters (friend is loaning me pumps temporarily)
Seal the tank
Build the heater module
I still need thermostats with submersible probes. The normally closed solenoid valve should be easy to find. Until I find thermostats I can use, heating is against a brick wall.
That's all that is left to do.
I have to replace the AC window unit with a heat pump/dehumidifier unit. Fortunately, 220 outlet is already there with existing unit.
Innovative hot water recirculation systems deliver hot water to fixtures quickly without waiting for the water to get hot. Rather than relying on low water pressure common in most water lines, recirculating systems use a pump to rapidly move water from a water heater to the fixtures.
In this system, a recirculating pump rapidly pulls hot water from a water heater while simultaneously sending cooled-off water from the hot water lines back to the water heater to be reheated. In addition to having the convenience of hot water on-demand, the system conserves water and can save energy.
Hot water recirculation systems can be activated by the push of a button, or by a thermostat, timer or motion sensor. Systems that use a thermostat or timer automatically turn on the pump whenever water temperature drops below a set-point, or when the timer reaches a setting. These systems ensure that hot water is always available at the faucet without any waiting.
Systems that use a thermostat or timer may use more energy than on/off button or switch operated systems, due to more frequent recirculation cycles and hot water constantly being left in the pipes to cool off.
Hot water recirculation systems generally consist of a pump, an integrated electronic controller, and a zone valve. When the activation button is pushed, or when another type of control turns the system on, the pump starts recirculating cooled water that's been sitting in the hot water line and sends it back to the water heater through the cold water line. When the water reaches a desired temperature a control closes the zone valve and turns off the pump. It is much like turning on the hot water faucet and letting the water run until it gets hot, but instead of the water going down the drain, it is simply returned back to the water heater. When the hot water faucet is turned on, hot water is readily available.
The system is designed to provide hot water at the most distant fixture and every fixture in series or close to the main line. All cold water fixtures still receive cold water, and the system is designed to not allow hot water to enter cold water lines. Only one pump is necessary to supply hot water to any fixture. Optional wireless remote control units let the user turn on the system from any faucet or fixture in the house.
In this system, a recirculating pump rapidly pulls hot water from a water heater while simultaneously sending cooled-off water from the hot water lines back to the water heater to be reheated. In addition to having the convenience of hot water on-demand, the system conserves water and can save energy.
Hot water recirculation systems can be activated by the push of a button, or by a thermostat, timer or motion sensor. Systems that use a thermostat or timer automatically turn on the pump whenever water temperature drops below a set-point, or when the timer reaches a setting. These systems ensure that hot water is always available at the faucet without any waiting.
Systems that use a thermostat or timer may use more energy than on/off button or switch operated systems, due to more frequent recirculation cycles and hot water constantly being left in the pipes to cool off.
Hot water recirculation systems generally consist of a pump, an integrated electronic controller, and a zone valve. When the activation button is pushed, or when another type of control turns the system on, the pump starts recirculating cooled water that's been sitting in the hot water line and sends it back to the water heater through the cold water line. When the water reaches a desired temperature a control closes the zone valve and turns off the pump. It is much like turning on the hot water faucet and letting the water run until it gets hot, but instead of the water going down the drain, it is simply returned back to the water heater. When the hot water faucet is turned on, hot water is readily available.
The system is designed to provide hot water at the most distant fixture and every fixture in series or close to the main line. All cold water fixtures still receive cold water, and the system is designed to not allow hot water to enter cold water lines. Only one pump is necessary to supply hot water to any fixture. Optional wireless remote control units let the user turn on the system from any faucet or fixture in the house.
I saw one of these recirculating addons in Home Depot tonight. I think it will suit my needs perfectly. Here's a further explanation of it;
http://www.chilipepperapp.com/cwrcs.htm
http://www.chilipepperapp.com/cwrcs.htm
- Status
